Show us your Gamebuino clone or the last module you made.
by spunky » Thu Mar 03, 2016 3:13 am
- ready to print at pcb shop,not shure if it will even work,i get 3 for £40 i think they will work,ive gone over the schematic enough times,shame the board is square lol its gona be small though 10cm x 8cm and it takes an sd card breakout,it plugs in on the left where the 6 pin header is,battery will go in center its got no charge circuit but will have a ftdi for bootloader etc i just hope ive got the screen leds lined up properly i can see that being a bugger but may be lucky with it.
- FINISHED.png (82.12 KiB) Viewed 16248 times
Last edited by
spunky on Thu Mar 03, 2016 3:29 am, edited 2 times in total.
-
spunky
-
- Posts: 10
- Joined: Thu Mar 03, 2016 3:03 am
by spunky » Thu Mar 03, 2016 3:19 am
- both my clones
- my clone 1.jpg (65.71 KiB) Viewed 16247 times
-
spunky
-
- Posts: 10
- Joined: Thu Mar 03, 2016 3:03 am
by spunky » Thu Mar 03, 2016 3:19 am
- my other clone
- my clone 2.jpg (70.68 KiB) Viewed 16247 times
-
spunky
-
- Posts: 10
- Joined: Thu Mar 03, 2016 3:03 am
by Retrogadgets » Sat Mar 05, 2016 9:51 am
spunky wrote:my clone 1.jpg
checkout
www.dirtypcbs.com you could have had 10 boards for £29.00 with a 10 days delivered back to you from china !
theyre great quality
-
Retrogadgets
-
- Posts: 8
- Joined: Sun Feb 14, 2016 3:53 pm
by albertinjo » Wed Mar 09, 2016 12:01 pm
Nice
Here's mine
Spunky your scrren is probabbly flickering? Mybe i'm wrong, anyway...put a large capacitor near the screen power supply and it should be a lot better... took me a while to figure out
- SAM_3259.JPG (215.81 KiB) Viewed 16178 times
-
albertinjo
-
- Posts: 98
- Joined: Wed Mar 26, 2014 2:26 pm
by spunky » Fri Sep 23, 2016 9:09 pm
Hi,my screen is ok no flicker or anything,my sound isnt that loud but its ok,i didnt amp it up with a transistor lol but it works fine,yours looks great.
-
spunky
-
- Posts: 10
- Joined: Thu Mar 03, 2016 3:03 am
by spunky » Fri Sep 23, 2016 9:10 pm
Why have you 3 switches at the bottom?
-
spunky
-
- Posts: 10
- Joined: Thu Mar 03, 2016 3:03 am
by rodot » Mon Sep 26, 2016 7:47 am
Albertinjo said in
this post that it was for backlight control and manual muting.
-
rodot
- Site Admin
-
- Posts: 1290
- Joined: Mon Nov 19, 2012 11:54 pm
- Location: France
-
by Retrogadgets » Fri Oct 07, 2016 6:13 pm
My gamebuino compatible - The MAKERbuino in partnership with Albert Gajšak
-
Retrogadgets
-
- Posts: 8
- Joined: Sun Feb 14, 2016 3:53 pm
Return to Hardware Gallery
Who is online
Users browsing this forum: No registered users and 6 guests